Maintenance Tips for Water Heaters

We rely upon a water heater day after day. Since they’re normally installed in the garage or basement, we don’t think too much about it till and we don’t have any hot water or we discover water leaking on the floor. Many water heaters can last for a long period because they have been given proper maintenance to extend their life. By extending the life of your water heater, you save money simply because you do not have to purchase a new one. Regular maintenance of the water heater must be on every homeowners’ honey do list. This maintenance needs to be scheduled at the minimum, once a year, according to the quality of water in the area up to two or three times per year.

Flush the water heater to get rid of built up sediment, calcium deposits along with other harsh particles. Make sure you turn the electric or gas off to the water heater. Drain the water heater by hooking up a garden hose to the valve found at the bottom of the tank. Water coming straight out of the tank can be quite hot, be careful when draining a water heater around small children and pets.

(C) plumberdoc.com

(C) plumberdoc.com

Close the water supply valve on the water inlet line entering your water heater. Then you’re able to connect a garden hose to the drain valve found at the bottom of the heater. Open the drain and enable it to run until all of the water has emptied in the heater. After that close the drain. Open the water supply valve and refill the heater. It’s also wise to open a hot water faucet somewhere inside and stand there and watch it run for several minutes until the water flows out easily.

After the Water Heater appears like it’s got drained close the relief valve (if you opened it) turn on the cold water valve for 15 seconds while the bottom valve is still open. After 15 seconds close the cold water valve again and let heater drain. This will likely eliminate virtually any remaining sediment on the bottom of the tank.

Apart from frequently flushing your water heater, plumbing experts also advise adding a water treatment system to your residence to filter or condition the water therefore it is less corrosive to your plumbing system, specifically in areas that have hard water. To get more methods to care for and protect your home plumbing system, make contact with a licensed, professional plumbing contractor in your area to discuss choices and products to suit your needs.

The point is that maintaining a water heater, while necessary, may be tedious and sometimes unpleasant perform. However if you are a DIY person, it could soon become a badge of honor in your household. If you prefer obtaining a plumber, you’ll be able to at least rest assured that you have saved a little time and avoided a messy activity.

 

3 Types of Residential Insulation

Insulation is supposed to reduce the flow of heat out of your home and to your home. Home insulation is an effective solution to stop heat loss or grow in the interior of the property by shielding it from the weather outside. This really is most cost effective if done while remodeling or renovating your property or if perhaps your would like to lower energy bills.

When selecting home insulation, the most significant aspect to consider is its R-value. This value is represented by a number – the higher the number, the far better the material is at retaining heat. For homes in chilly climates, a higher R-value helps keep your energy bills low by making the most of your energy efficiency.

You can find four different types of insulation you should know about when considering your property.

(C) Energyvanguard.com

(C) Energyvanguard.com

Fiberglass Insulation: Fiberglass is regarded as the typical insulation in the U . S . and is made use of in both residential and commercial property. Fiberglass is available in two different forms; batt and blanket. Batt insulation comprises of rock wool or the fluffy fiberglass you think of. It usually comes in 4 to 8 foot lengths with a variety of various widths. Blanket insulation is very much like batt except it is made in continuous rolls. This makes for less waste but is more challenging to handle.

Loose-Fill Insulation: This is commonly made of fiberglass, rock wool, or cellulose and is available in small particles. It’s put in by being blown in to the space using a specific pneumatic blower. It is always good for adding insulation to existing areas, strangely shaped areas and around obstacles.

Foam Insulation: Foam is also utilized to insulate closed spaces like walls, ceilings and floors After the foam is injected into an empty space it’s going to expand and harden to provide excellent R-values. Foam is among the most expensive form of insulation and you will probably ought to hire a professional should you be looking to insulate a large area.

Rigid Foam Insulation: This kind is considered the most high-priced of all insulation materials yet the most effective mainly because it has the top tolerance for moisture. Whilst typically more costly than fiber products, it’s very effective in buildings with space limitations and where higher R-values are essential. It is usually utilized in unfinished walls; ceilings and floors; and unvented low-slope roofs.

 

Understanding How Central Air Conditioners Are Rated

Central air conditioners form a common feature in most of the houses of the country. Such heat absorbing devices plays a major role in filtering, cooling and dehumidifying the air. There are many factors that have to be considered while making any worthy purchase.

 

If you are wondering about whether a high efficiency air conditioner is worth the price, consider the central air conditioner ratings to help make your decision.

 

Understanding SEER

Central air conditioners are rated by what is known as the Seasonal Energy Efficiency Rating, or SEER. To be sold in the United States, a central air conditioning system must have a SEER of 13 or higher. High efficiency models can have a SEER up to 21.

So what is SEER and what makes it so important to your air conditioning system? SEER is an efficiency rating, much like the miles per gallon on your car; the higher the miles you get to the gallon the less you pay at the pump. Air conditioners work the same way; SEER refers to the amount of cooling output you receive from your unit, divided by the amount of energy it takes to run the unit. The higher the SEER, the less you’ll spend on electricity to cool your home.

Ratings for Central Air Conditioners

When you purchase a new central air conditioning system, you’ll want to know several things such as how many square feet it can cool and how efficient the system is. This is where SEER comes into play. While a rating from 13 to 14 might not seem like much except a higher price tag on the unit, going up just one SEER point in a rating can save you as much as 10% on your energy bill this summer. Increase this to a high efficiency unit that has a rating of 21 and you’ll save as much as 80% over a lower efficiency model.

While you pay up-front for this privilege, with higher price tags on the higher efficiency models, you can save a lot over the lifetime of an air conditioning system.

Choosing a Central Air Conditioning System

When you consider central air conditioner ratings at your time of purchase, make sure you also take into account how much use your unit will receive. If for example you live in Northern Maine and only run the central air conditioning for a few days each summer, you aren’t going to make up the difference in the purchase price of a higher efficiency model. On the other hand, if you live in Southern Florida and will be running your central air conditioning year round, an air conditioning system with a high SEER is going to save you a lot of money over the life of the unit.

To make your decision on which unit is going to be best for you, you may want to consider how much you spend in energy bills on the hottest months of the year. Now look at the percentage drop from a high to a low energy rating and compare it with the cost of the air conditioner. Remember that most air conditioning systems last on ..

 

Read more: http://homeimprovement.lovetoknow.com/Central_Air_Conditioner_Ratings

What’s That Funny Smell When the Heat Turns On?

If there are some strange smells coming from your HVAC system, you may be facing a furnace repair job. Do not these smells because it may mean a major disaster later on.

 

If you notice an odd burn smell when the heat turns on, it may be a sign that your furnace needs maintenance.  It could be something as minor as a dirty filter, but it could also be a serious problem like a broken electrical component in the furnace. Don’t ignore it. Try to find the source of the odor to avoid costly repairs in the future.

You should not ignore a foul burn smell.  Try to find the source of the odor to avoid costly repairs in the future. If your furnace smells like burning rubber or burning plastic, it could be a small problem or a major situation. If your furnace smells like smoke, it could likewise indicate a blocked chimney, so in any case you need to address the burning smell immediately

Here are some tips to get you started.

What causes the smell of burning dust?

When your furnace is not used for long periods of time, dust can collect on the heat exchanger and in the air ducts. When the furnace is turned on, the dust burns off and releases an odor.

It is normal for dust to burn off when the heater is turned on for the first time in the winter season and not a cause for concern. This smell should disappear in a few hours. If the problem persists, check your air filters.

What causes musty odors?

When you turn on your furnace for the first time each year, it may smell like a damp basement or like dirt or dust. The musty odor comes from dust and dirt collecting in the air ducts, which gets blown throughout your home when the furnace turns on. If this smell persists throughout the heating season, it could mean you need to change the air filter.

 

Read more: https://www.angieslist.com/articles/whats-funny-smell-when-heat-turns.htm

The Importance Of HVAC Cleaning

The HVAC system of a residence ensures the house of acceptable indoor air quality, as well as the thermal suitability of the property. Unknown to the homeowners these trapped dusts can be inhaled in the air specifically causing asthma attacks on small children as well as other upper respiratory diseases. Harmful molds could also grow inside HVAC system.

(c) gentecservices.com


1. Duct cleaning could improve your overall health. With respect the U.S. Environmental Protection Agency, indoor air might be up to 70 times much more polluted than outdoor air. Bacteria, pollen, dust mites, as well as other contaminants all can reside in a building’s ventilation system, contributing to breathing difficulties, allergy flare-ups and other problems. Visible mold in an air duct is a particular problem and ought to be tackled immediately, as should rodent or insect infestations. A professional HVAC cleaning can help take away these contaminants and enhance the health of you and your family.

2. Duct cleaning can help your HVAC system go longer. Whenever grime and dirt get trapped in your heating and cooling system, they might at some point cause it to break down. Regular duct cleaning may help lengthen living of heat exchangers, fans and cooling coils, assisting you avoid expensive repairs later on. Keeping your HVAC system clean also means it does not have to function as hard to heat and cool your home, which may also help it go longer.

3. Duct cleaning offers energy savings. When the system is slow, there is a chance that you will get higher power bills at the end of the month. There’s no question, once the machine is working out from order, it’s going to lose its energy. By on-time servicing of the unit, you will be able to save far more as compared to just the HVAC system. You will save money which is wasted through extra energy bills.

4. HVAC operates at an optimum performance. If the unit is dirty from the inside, all its components, such as net, filter and exhausts are covered in dust. This decelerates the unit and there is a decrease in the efficiency of the system. Once the system becomes slow, it shows that the unit is working to provide less. As long as the servicing and cleaning of the system is done regularly, it’s going to work at its the best possible efficiency.

5. Prevent nasty odors. A musty or “moist” odor in your house could mean that mold and/or mildew is lurking in your air ducts. Air fresheners, scented candles or incense only will mask dirty air for a short while. Professional cleaning can take away the smells almost entirely in a very short while.

 

Air Purifier Buying Guide

(c) consumerreports.org

Air purifiers in homes, offices and public spaces ensure that the air we breathe is free of pollutants, allergens, and odors. Many people make use of indoor air cleaning systems to clean the air. Often, the best solution is to add a filtration module to the air conditioning or heating system. One other alternative is to try using a portable air purifier. Most pros suggest employing an air purification system that utilizes HEPA or high efficiency particulate air filters.

When choosing an air purification system you need to consider:

1. HEPA filtration performance. A traditional HEPA filter uses millions of tiny fibers to help capture at least 99.7% of all of the contaminates in the air.

2. The size of the room and the capacity of the air purifier system. Unless the two are compatible the efficiency will be largely reduced.

3. Check out the noise level of the air cleaner before making your purchase.

Here are a few tips given by experts in air purification systems:

1. Figure out your requirements. Examine aspects like size of room, air currents, traffic, and use.

2. Reading through type of purifying technologies. Passive technology consists of purifying air by drawing it to the purifier. The air drawn goes through the filters, present in the purifier, thus purifying the air from contaminants, micro-organisms, allergens, airborne dust, pollen, odors, gas, etc. Active technology is a technology, where air is purified outside the purifying unit by producing some sort of effect in the air.

3. Find out how big of air purifier will work efficiently. Experts say always choose a size or capacity higher than the one recommended this can guarantee that the air purification is efficient even if there is an overload.

4. Determine your options and the costs. Always compare and contrast products and aspects like after sales service and recurring costs.

5. Check with your doctor and other health professionals exactly what the benefits and drawbacks of air purification systems are and what would be perfect to your individual needs.

6. Most air purification systems have regular maintenance requirements. Therefore determine about servicing the filters and changing them. Follow the suggestions of the manufacturer.

Which kind of air purifier you are purchasing matters more than where you shop. Should you be looking for an affordable but well performing air purifier, you should be ready to spend a little bit of time researching all of the available options.

Researching is your first priority when looking for an air cleaner. So carry out thorough research. Check out credible publications, consult HVAC and doctors, and take advice from any trusted friends or acquaintances using purifiers.

How to Maintain Hot Water Heating Systems

A good boiler maintenance plan consists of observing, adjusting, cleaning and lubricating various pieces of mechanical equipment on a regular basis. Boiler maintenance is either protective or corrective.

 

Hot water heating systems need a little maintenance, like venting the radiators and draining the boiler, to keep things running efficiently. Gravity and hot water furnaces are not often installed in new homes today, but similar systems with the old cast-iron radiators throughout the house were fixtures in homes built around 1900, and some of them are still working. Clanking, popping, and gurgling as they swing into action whenever the thermostat detects room temperatures dropping, they provide a relatively steady flow of heat without the drafts you get in forced-air furnaces.

Hot water systems are closed, meaning that the water constantly circulates through the pipes and into the boiler. Newer units have many zones with two water pipes linked to each zone: one circulating heated water to the rooms and the other returning the much cooler water back to the boiler to get reheated. In the older one-pipe series systems, hot water flowed from room to room, and then back again to the boiler in the same pipe. The last room on the circuit never got as warm as the first.

To maintain a system, you should lubricate the circulating pump motor. Use a lightweight oil such as 3-in-1, and pour it in the oil cup.

In the fall and throughout the heating season, you also need to vent or purge radiators that don’t have an automatic purge system. To vent the radiator and drain the boiler, follow these directions:

  1. Open the valves on radiators and convectors to let out air.

    Keep them open until water starts coming out. Be ready to catch the water in a bucket or container.

  2. Close the valve.

    Don’t forget to drain the boiler to get rid of rust and mineral deposits. Read the manufacturer’s instructions, and then follow these steps:

  3. Turn off the power and water.

    Instead of the old cast-iron radiators, today’s units have free-standing or baseboard convectors. They’re less bulky, more efficient, and look much nicer than their ancestors and they provide the same amount of heat to all the rooms. The disadvantage of hydronic or hot water heat is that, because there is no duct work, you can’t have central air.

 

Read more: http://www.dummies.com/home-garden/interiors/ventilation/how-to-maintain-hot-water-heating-systems/

Make Your Home Energy Efficient

Image result

(C) remodelerlife.com

Imagining life without power is extremely problematic especially when we depend on electrically powered gadgets for a lot of our day to day function. Yet, we could not erase the truth that there’s a stop to everything. Even energy resources are now reducing leaving us a reminder that we should start off the change now. One way to the energy preservation is by your own residence In some cases many people have the tendency to waste a lot of energy since they are not thoroughly conscious of our environmental condition. They do not know that in just their simple acts, a huge progress could happen.. Irrespective of whether both at home and in the office, there are a lot techniques that people can adhere to ensure that we are able to conserve energy and help conserve our world. Listed here are a few of the basic steps;

Do an energy audit!

Choosing to make the home energy efficient a very good idea however, you can start doing things randomly. After all, before you take actions to further improve, you have to learn which aspect should you concentrate on. Energy audit will help you examine this. This is an easy procedure where every part of the property is properly checked so that you can know the aspects which are resulting in an increase in your power consumption. You could ask a pro specialist or energy inspector to do the job. They’ll ask for a reasonable fee and provide you a detailed report in just a few hours.

Seal the leaks!

Air sealing is the process of sealing leaks in a building envelope to limit the amount of air that leaks out of and into the house. The air leaks through the envelope such as the outer walls, windows, doorways, along with other openings. As a result there’s a waste of a lot of energy therefore heightens your utility costs. A well-sealed envelope can create a real difference on your utility bills and energy utilization.

Try insulation

In simple terms, insulation is a thick layer between house and the external environment. In summer season, this insulation keeps the temperature from getting inside your home and raising the temperatures. On the other hand, during winter, this insulation keeps the property pleasant and warm by preventing the heat from escaping. Don’t settle for too cold or too hot

Whilst making use of air conditioning units or heaters, always remember to go for temperatures which make you feel comfortable rather than opting for an extreme climate. As an illustration, when you’re using an air conditioner, there is no sense in maintaining icy cold temperatures and wearing sweaters even when you are inside.

You’ll find simple tricks that may be easily applied within your daily routine to make your premises more energy efficient in a reasonably shorter period of time.

Boiler Maintenance, Because You Work Hard For Your Money…

The boiler in your household plays a vital role in keeping your home warm during the cold winter months. It is important to keep your boiler maintained and serviced to ensure maximum performance.

 

With our boiler maintenance tips you can do it yourself and save. A hvac service call will normally cost around $100. With a little help, you can do it yourself and keep the $100.

And, while you are at it, we will show you some simple improvements you can make. These improvements will not only save you money in operation but also help your system to last longer. (The normal boiler maintenance call would not include tips to improve your current system’s performance.)

If your unit uses gas or oil, you should start by examining the vent pipes. For an 80% efficient unit this will be made of metal. You should check for rust and make sure the pipe is not blocked. Sometimes, birds will make nests in these. Also, you should make sure that the connections are not coming apart.

For a 90% unit, they will be made of pvc. You should make sure the joints are not coming apart and that the pipes are not blocked.

Next, you should check the inside for excessive dirt or rust. You can clean as necessary with a vacuum cleaner but make sure you turn off the power first.

Now you should oil the circulator pump and motor if it has oiler ports. Most of the newer pumps do not require oil.

You should also check your thermostat(s). If they are not digital, they must be perfectly level. If they are not they lose their accuracy.

**HOT TIP** Replacing your old thermostat(s), if they are the old mechanical type, with digital units is a very inexpensive improvement. It is an easy diy project that can pay big dividends!

Now, you can start the system by turning up the thermostat. Allow the system to heat up. Then, if your radiators have manual air vents on them, you should bleed the air out of the system. With a small screwdriver, you crack open the vent until water starts to come out. Then, you move on to the next one.

 

Read more: http://www.hvac-for-beginners.com/boiler-maintenance.html

Cool Air Anywhere With Evaporative Cooler

Probably the most cost-effective ways to cool your living or working space is with evaporative coolers. Evaporative coolers, also referred to as Swamp coolers are helpful machines for people who are looking to cool their properties. These coolers are among the safest, most effective and environment-friendly cooling systems available in the market. It is mechanics and concept is pretty simple and it can efficiently cool and area without consuming a great deal of resources and energy. This is actually the perfect cooling system for those who are working with a tight budget.

Image result

(C) Lowe’s

Evaporative air coolers are used by many home owners for years; however some people are not aware of them. They can assist in bring down your energy bills by more than 25 percent and are proved to be a good energy-saving alternative to air conditioners. An additional advantage they have over air conditioners is they need very little maintenance, so you don’t need to spend your hard-earned money on repairs and servicing.

An evaporative air cooler functions on the principle of an endothermic reaction. An endothermic reaction is a procedure that absorbs energy by means of heat. The evaporative air cooler passes air via a wet media. As the air goes through the water in the wick evaporates and the reaction triggers heat in the air to be absorbed.

You can find several of evaporative designs that individuals can purchase. You need to evaluate your need like space, cooling capacity so that you won’t have to spend much on a very expensive type. In choosing a swamp cooler, you should note the unit’s air moving capacity, as well as set up and maintenance requirements. Some swamp coolers may need more work than portable air conditioners such as replenishing the water supply, draining the unit, and cleaning the cooling pads. Nevertheless, evaporative coolers are created by using a simplistic design; hence they have very minimal servicing need.

Prior to deciding to install an evaporative cooler, ensure that you check the building codes of your area. After you’ve examined the codes, you need to decide on the location and mark the opening. You must then construct a platform of iron or wood and attach the platform to the opening. When fixing the platform, don’t forget to do not cut any structural framework. The dimensions of the opening and the structure are determined by the directions that come with the machine. If you’re not knowledgeable with it, you may seek professional help to keep away from damage and further accidents

People who are planning to buy an evaporative cooler, you need to check out information on various brands available for sale.